故障代码

错误含义

具体描述

FIP/Corrective Action

-

Y Toner Life Warning

黄色碳粉寿命警告

The yellow toner cartridge has reached the set toner supply time limit but it can still work.

黄色碳粉盒已达到规定时限碳粉供应，但它仍然可以工作。

FIP-1 75

-

M Toner Life Warning

红色碳粉寿命警告

The magenta toner cartridge has reached the set toner supply time limit but it can still work.

红色碳粉盒已达到规定时限碳粉供应，但它仍然可以工作。

FIP-1 76

-

C Toner Life Warning

青色碳粉寿命警告

The cyan toner cartridge has reached the set toner supply time limit but it can still work.

青色碳粉盒的已达到规定时限碳粉供应，但它仍然可以工作

FIP-1 77

-

K Toner Life Warning

黑色碳粉寿命警告

The black toner cartridge has reached the set toner supply time limit but it can still work.

黑色碳粉盒的已达到规定时限碳粉供应，但它仍然可以工作

FIP-1 78

-

Toner Bottle Life Warning

碳粉满警告

The waste toner bottle is detected FULL by the SENSOR TNER FULL but can still work

废碳粉检测传感器到检测废碳粉瓶满，但仍然可以工作。

FIP-1 79

-

Xero CRU Life Warning

感光鼓(CRU)寿命警告

The drum has exceeded its specified rotation count but it can still work.

鼓已超过其指定的旋转数，但它仍然可以工作。

FIP-1 80

%s Check paper

％本票纸

IOT Paper Size Mismatch

互操作性测试纸张尺寸不匹配

Paper Size Mismatch detected.

纸张尺寸不匹配检测。    (打开/关闭托盘或删除旁路纸盘并重新加载文件)

Open/close the tray or remove and reload paper in Bypass Tray.

(No LCD Display)

无液晶显示器

Static Jam (Remain at OHP)

静态果酱（留在铂）

The SENSOR OHP was turned ON at Power ON or when the I/L was closed. (Static Jam)

该传感器铂被打开或上电时的I / L的关闭。（静态果酱）

FIP-1 39

001-358

IOT Fan Error Fuser

互操作性测试范错误定影

Fan Error Fuser detected.范错误定影检测。

Power OFF/ON

001-360

IOT Fan Error Rear

范错误后互联互通

Fan Error Rear detected.范后发现错误。

Power OFF/ON

003-356

NVRAM ErrorNVRAM中错误

An error occurred in the NVRAM on the PWBA MCU.

错误发生在微控制器上的PWBA NVRAM中。

FIP-1 43

004-310

Communication Error Feeder

直属通信错误

A communication error occurred between the PWBA MCU and the feeder.

阿之间发生的通讯错误的PWBA MCU和接驳。

FIP-1 40

004-311

Communication Error Duplex

通讯错误双工

A communication error occurred between the PWBA MCU and the Duplex.

阿之间发生的通讯错误的PWBA MCU和双工。

FIP-1 41

004-321

TR0 Failure

TR0传感器故障

The PWBA MCU did not receive the output signals from the SENSOR TR-0 (TR0 Sensor) at the specified timing.

PWBA MCU没有在指定定时方面收到从传感器TR-0((TR0传感器)输出信号.。

FIP-1 44

004-324

Humidity Sensor Error

湿度传感器错误

The inputs from the SENSOR HUM & TEMP are out of the specifications.

从本田和温度传感器的输入，是从规格

FIP-1 58

004-332

Deve Home Position Sensor Error

德韦首页位置传感器错误

The PWBA MCU did not receive the output signals from the Rotary Home Position Sensor within the specified time after the Rotary Developer had started rotation.

在指定作为时间以内PWBA MCU 不确实收到从旋转的国内位置传感器从输出到信号，在旋转的开发者已经以开始转动之后。

FIP-1 46